Skip to main content
Fisher & Paykel Product Help

Installation instructions

Please follow the installation steps below to ensure your appliance operates correctly.
Dimensions and clearances
  • The cooker must be installed no less than 50 mm away from any side walls which exceed the height of the cooktop.
  • The cabinetry surrounding the cooker must be made of heat-resistant material and must be able to withstand temperatures of 65 °C above room temperature.
  • Do not install the cooker near flammable materials (eg curtains).
  • If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place.
Locating the area for electrical connection

Fig. 1 Area for electrical connection
 


Fig. 2 Dimensions and distances from cooker
 

Fig. 3a Screw/unscrew the feet to get the required height

Leveling the cooker

Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface. 

  • For ease of installation, first remove the kickstrip. To remove the kickstrip, unscrew the two screws holding it in place.
  • The cooker is already fitted with four levelling feet.
  • Level the cooker by screwing or unscrewing the feet.
  • Make sure you follow the instructions in Figs. 3a, 3b, and 3c.
  • Note: nuts are supplied with the cooker in a separate kit.
    Do not refit the kickstrip until you have installed the anti-tip bracket.

Fig. 3b Do not use the supplied nuts for height adjustments between 0 and 8mm

Fig. 3c Use the supplied nuts for height adjustments between 8 and 13mm

Fitting the anti-tilt bracket 

To restrain the appliance and prevent it tipping accidentally, the anti-
tilt bracket and restraining plate supplied must be fitted according to the instructions below.

  1. Drill four 8mm diameter holes for the fixing screws (two in the wall and two in the floor-see Fig.4) and insert the plastic plugs supplied. bracket

Before drilling the holes, check that you will not damage any pipes or electrical wires. 

  1. Attach the anti-tilt bracket to the floor and rear wall using the four screws supplied, as shown in Fig. 4.
     
  2. After attaching the anti-tilt bracket securely, slide the cooker into place. Ensure that the left rear foot slides under the bracket, as shown in Fig.4.
     
  3. Access the bracket by removing the drawer (Fig. 5).
    1. Slide out the drawer completely.
    2. Press the lever of the left guide rail down and pull the lever of the right guide rail up.
    3. Holding the levers, disengage and remove the drawer.
       
  4. If fitted, remove the kickstrip (see ‘Leveling the cooker’). Fix the restraining plate by sliding it into place and securing it with the fixing screw and washer supplied. See Fig. 6.
     

  5. Replace the drawer (Fig. 7):

    1. Insert the drawer rails into the guide rails.

    2. Gently push the drawer in completely; the safety catches will automatically hook.

  6. Replace the kickstrip using the two screws.

    Beware of sharp edges when removing or replacing the drawer.


Fig. 4 Attaching the anti-tilt bracket and sliding the cooker into place
 


Fig. 5 Accessing the anti-tilt bracket by removing the drawer
 


Fig. 6 Fixing the restraining plate
 


Fig. 7 Replacing the drawer

Moving the Cooker

To prevent damaging the adjustable feet or lower trim, ensure the cooker is always lifted by two people.
 

Do not lift the cooker by the door handles.
DO NOT DRAG the cooker. Lift the feet clear of the floor.
 

Take extra care not to damage the door sensor (top left of oven).

Fig. 8 Correctly lifting the cooker

Fig. 9 Incorrectly lifting the cooker

Fig. 10 Incorrectly moving the cooker

Fixing the backguard

Before installing the cooker, assemble the backguard “C” .

  • The backguard “C” can be found packed at the rear of the cooker.
  1. Before assembling, remove any protective film/adhesive tape.
  2. Remove the two spacers “A” and the screw “B” from the rear of the cooktop.
  3. Assemble the backguard as shown and fix it by screwing the central screw “B” and the spacers “A”.

Fig. 11 Assembling the backguard

Connecting the power supply cable

This cooker must be connected to the electricity supply only by an authorised person.

To connect the power supply cable to the cooker, it is necessary to:

  1. Unhook the terminal board cover by inserting a screwdriver into the two hooks ‘A’ (fig. 12).
  2. Unscrew the screw ‘D’ and open completely the cable clamp ‘E’ (figs. 14).
  3. Position the U bolts ‘F’ onto terminal board ‘G’ (figs. 14) according to the diagrams in fig. 13.
  4. Connect the phase, neutral and earth wires to terminal board ‘G’ according to the diagrams in figs. 13 - 14.
  5. Strain the feeder cable and block it with cable clamp ‘E’ (by screwing screw ‘D’).
  6. Close the terminal block cover (check the two hooks ‘A’ are correctly hooked).

To connect the power supply cable DO NOT unscrew the screws fixing the cover plate behind the terminal block.
WARNING: If the power supply cable is damaged, it must be replaced only by an authorised service agent in order to avoid a hazard.

Voltage and power consumption

220-240/380-415 V 3N~    50 Hz 47.2A (230V) 10850 W (diversity not applied)

Fig. 12 Terminal block

Fig. 13 Connection diagrams

Feeder cable section

In Australia and New Zealand: this cooker must be connected to electrical supply using V105 insulated cable.

220-240 V~

3 x 6 mm2 (*)

380-415 V 3N~

5 x 2,5 mm2 (*)

380-415 V 2N~

4 x 6 mm2 (*)

* Connection with wall box connection.

  • Diversity factor applied.
  • A diversity factor may be applied to the total loading of the appliance only by a suitably qualified person.
ELECTRIC DIAGRAM KEY

F1 Oven switch
ST Safety thermostat
STL Safety thermal overload
TL Thermal overload
TL1 Induction hob thermal overload
PR Electronic programmer
PB Temperature probe
TS Oven temperature selector
EC Oven function selector (encoder)
SF State functions
DL Door lock device
DS Door sensor
R1 Relay 1

R2  Relay 2
R3  Relay 3
LF Oven lamp
TR Oven lamps transformer
S1  Door lock indicator lamp
S2  Line pilot lamp
C Oven top heating element
G Oven grill heating element
SI Oven bottom heating element (int.)
SE Oven bottom heating element (ext.)
CI Oven circular heating element
IU-LH Induction unit, left zones
IU-RH Induction unit, right zones

UD Induction units user display
PCB Induction units PCB
RSI Rotary selector interface
DLM Door lock motor
GIR Rotisserie motor
V Oven fan motor
CF Cooling fan motor
RS Resistance (220 Ohm)
R Product relay
M Terminal block
T Earth Connection

  • Was this article helpful?