Skip to main content
Fisher & Paykel Product Help

Installation instructions - Ceramic Glass Cooktop Models

Please follow the installation steps below to ensure your glass cooktop operates correctly.

Ceramic Glass Cooktop Models

Dimensions and clearances

  • The cooker must be installed at least 50 mm away from any side walls higher than the cooktop. The cabinetry surrounding the cooker must be made of heat-resistant material and must be able to withstand temperatures of 65 °C above room temperature.
  • Do not install the cooker near flammable materials (eg curtains).
  • If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place.

Fig. 15 Dimensions and correct distances from cooker

Levelling the cooker

Using the supplied adjustable feet is MANDATORY. For safety reasons and to ensure adequate ventilation, the cooker chassis MUST NOT sit directly on the floor, a plinth, or other support surface.

To fit the adjustable feet:

  1. Rest the rear of the cooker on a piece of packaging, exposing the base for fitting the feet.
  2. Screw the four feet to the cooker.
  3. Stand the cooker and level it by screwing or unscrewing the feet with an adjustable spanner. Use the supplied nuts if necessary. See Figs. 16a- 16d.


Fig. 16a Fitting the adjustable feet (supplied with the cooker in the feet kit)

Fig. 16b Do not use the supplied nuts for height adjustments between 0 and 8 mm.

Fig. 16c Use the supplied nuts for height adjustments between 8 and 15 mm.

Fig. 16d Levelling the cooker

Fixing the backguard

Before installing the cooker, assemble the backguard “B” .

  • The backguard “B” can be found packed at the rear of the cooker.
  1. Before assembling, remove any protective film/ adhesive tape.
  2. Remove the three screws “A” from the rear of the cooktop.
  3. Assemble the backguard as shown and fix it by screwing the three screws “A”.

Fig. 17 Assembling the backguard

Fitting the anti-tilt bracket

To restrain the appliance and prevent it tipping accidentally, fit a bracket to its rear to fix it securely to the wall. Make sure you also fit the supplied lock pin to the anti-tiit bracket.

To fit the anti-tilt bracket:

  1. After you have located where the cooker is to be positioned, mark on the wall the place where the two screws of the anti-tilt bracket have to be fitted. Please follow the indications given in Fig.18a.
  2. Drill two 8 mm diameter holes in the wall and insert the plastic plugs supplied.

Fig. 18a Fitting the anti-tilt bracket 

Before drilling the holes, check that you will not damage any pipes or electrical wires.

  1. Loosely attach the anti-tilt bracket with the two screws supplied.

  2. Move the cooker to the wall and adjust the height of the anti-tilt bracket so that it can engage in the slot on the cooker’s back, as shown in Fig.18a.

  3. Tighten the screws attaching the anti-tilt bracket.

  4. Push the cooker against the wall so that the anti-tilt bracket is fully inserted in the slot on the cooker’s back.

  5. Access the bracket and fit the lock pin;

  • Remove the drawer (Fig. 18b).
  • Fit the lock pin through the bracket, as shown (Fig.18c).
  • Refit the drawer.

Fig. 18b Removing the drawer

Fig. 18c Fitting the lock pin through the bracket

Connecting the power supply cable

This cooker must be connected to the electricity supply only by an authorised person.

To connect the power supply cable to the cooker, it is necessary to:

  1. Remove the screws that hold cover “A” behind the cooker (Fig. 19b).
  2. Position the U bolts “C” onto five-pole terminal block “B” according to the diagram in Fig. 19a.
  3. Feed the power supply cable through the cable clamp “D”. The supply cable must be of a suitable size for the current requirements of the appliance; see ‘Power supply cable section’.
  4. Connect the phase wires to the terminal block “B” and the earth wire to the terminal “PE” as shown in Figs. 19a-19b.
  5. Take up any slack in the cable and secure with the cable clamp “D”.
  6. Replace the cover “A”.

The earth wire must be left about 30 mm longer than the others.

Voltage and power consumption

230 V~ 50 Hz 9700 W (diversity not applied) 240 V~ 50 Hz 10550 W (diversity not applied)

Power supply cable section

This cooker must be connected to the electrical supply using V105 insulated cable.

230-240 V~ 3 x 4 mm2

Fig. 19a Connection diagram

Fig. 19b

Wiring Diagram

ELECTRIC DIAGRAM KEY

F1 Oven switch
F4/5 Energy regulators (single zones) F2/3 Energy regulators (double zones) LF Oven lamp
TM Oven thermostat
TS Safety thermostat
PR Electronic programmer
C Top heating element
G Grill heating element
S Bottom heating element V Fan motor
CIR Circular heating element CR Residual heat lamp
S1 Thermostat pilot lamp
S2 Radiant heaters pilot lamp
P3/4 Single zone radiant heaters
P1/2 Double zone radiant heaters
M Terminal block
T Earth connection CF Cooling fan motor TL Thermal overload
  • Was this article helpful?