Skip to main content
Fisher & Paykel Product Help

Water Softener Filter

 

 

Certain models are fitted with a water softener filter. If this is not the case with your model, you are recommended to purchase one from an approved supplier. To use the filter correctly, follow the instructions below.

 

Installing the filter

  1. Remove the filter from the packaging.
  2. Press Water Hardness.PNG.
  3. Press Left Arrow_Black.PNG or Right Arrow_Black.PNGuntilFilter.PNGWATER FILTER appears on the display.
  4. Press .
  5. TURN DATE INDICATOR TO DISPLAY NEXT 2 MONTHS: turn the date indicator disk until the next two months of the year are displayed. Press NEXT.
Water Softener Filter.PNG

The filter lasts about two months if the appliance is used normally. If the coffee maker is left unused with the filter installed, it will last a maximum of three weeks

Water Softener Filter #1.PNG Water Softener Filter #2.PNG
  1. RUN WATER INTO FILTER HOLE UNTIL IT COMES OUT FROM OPENINGS: To activate the filter, run tap water through the hole in the filter as shown in the figure until water comes out of the openings at the side for more than a minute. Press NEXT.
  1. Extract the tank from the appliance and fill with water.
  2. IMMERSE FILTER IN THE WATER TANK LETTING AIR BUBBLES ESCAPE. Place the filter in the water tank immersing it completely for about ten seconds, allowing air bubbles to escape. Press NEXT.
Water Softener Filter #3.PNG Water Softener Filter #4.PNG
  1. Insert the filter into the filter housing and press as far as it will go. Press NEXT.
  2. INSERT WATER TANK: Close the tank with the lid, then place the tank back into the appliance.
  1. PLACE 2L CONTAINER UNDER SPOUTS, press Tick_Select Button for Oven.PNG TO FILL FILTER: Container has to hold at least 0.5L Delivery begins and stops automatically. TheFilter.PNGsymbol appears on the display alongside the time to indicate that the filter has been enabled.

You can now use the coffee maker.

 

Replacing the Filter

Replace the filter whenExclamation.PNG REPLACE WATER SOFTENER FILTER, PRESS OK TO START appears on the display: to replace immediately, press Tick_Select Button for Oven.PNGand follow the instructions from point four.

To replace the filter later, press BACK. The Filter.PNGsymbol appears on the display to remind you that the filter needs replacing.

  1. Remove the tank and exhausted filter.
  2. Remove the new filter from the packaging.
  3. Press Water Hardness.PNG.
  4. Press Left Arrow_Black.PNG or Right Arrow_Black.PNGuntil Filter.PNG WATER FILTER appears on the display.
  5. PressTick_Select Button for Oven.PNG.
  6. Filter.PNGREPLACE FILTER appears on the display.
  7. Press Tick_Select Button for Oven.PNG.
  8. Follow the actions described in the previous section from point five. The filter is now active and you can use the coffee maker.
After two months (see date indicator) or when the appliance has not been used for three weeks, you should replace the filter even if the ‘replace filter’ message has not yet been displayed.

 

Removing the Filter

If you want to use the appliance without the filter, you must remove it and alter the settings in the appliance.

  1. Extract the tank and exhausted filter.
  2. Press Water Hardness.PNG.
  3. Press Left Arrow_Black.PNG or Right Arrow_Black.PNGuntil Filter.PNG WATER FILTER appears on the display.
  4. Press Tick_Select Button for Oven.PNG.
  5. Filter.PNGREMOVE FILTER appears on the display.
  6. Press Tick_Select Button for Oven.PNG.
  7. Exclamation.PNGCONFIRM REMOVE FILTER: press Tick_Select Button for Oven.PNG (or press BACK to go back to the settings menu).
  8. Exclamation.PNGFILTER REMOVED: the change has been saved. Press Tick_Select Button for Oven.PNG.

 

 

 

  • Was this article helpful?