Skip to main content
Fisher & Paykel Product Help

Installation

Installing the appliance.

Proximity to side cabinets

Screen Shot 2018-01-08 at 12.18.44 PM.png
  1. This range may be installed directly adjacent to existing 36” (914 mm) high base cabinets.
    Range dimensions:

     

  • Width: 29” 7/8 (759 mm)
  • Depth: 24” 3/16 (615 mm)
  • Height (without back guard): MIN 35” 21/32 (906 mm) - MAX 36” 11/32 (923 mm)
  • Back guard (height): 3” (76 mm)

Gas line opening: Wall - 37/64” (14.5 mm) from the right side to centre of range; from 5” 7/16 (138 mm) to 6” 1/8 (155.5 mm) [depending on feet regulation] from the floor.

Grounded outlet: should be located 37/64” (14.5 mm) from the left side to centre of range; from 5” 7/16 (138 mm) to 6” 1/8 (155.5 mm) [depending on feet regulation] from the floor.
The electric cord with 4-prong ground plug (NEMA 14-50P) shall have a minimum length of 48” (1220 mm) beyond the back of the appliance.

  1. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36” (914 mm) high.
    There must be a minimum of 11” 13/16 (300 mm) side clearance from the range to such combustible surfaces TO THE LEFT or TO THE RIGHT above the 36” (914 mm) high countertop.
    One side (left or right) above the 36” (914 mm) high countertop must always be kept clear.

    Island installation: There must be a minimum of 12” (305 mm) clearance from the rear of the back guard to such combustible surface on the back of the range above the 36” (914 mm) high countertop.
  1. The maximum upper cabinet depth recommended is 13” (330 mm). Wall cabinet above the range must be a minimum of 30” (762 mm) above the countertop for a width of minimum 30” (762 mm): it has to be centered with the range. Side wall cabinets above the range must be a minimum of 18” (457 mm) above the countertop.

Gas and Electric connection

fixed41_720.png

Reference Inch mm
A 5” 7/16 - 6” 1/8 (*) 138 - 155.5 (*)
B 14” 3/8 365
C 37/64” 14.5

(*) : Depending on feet regulation

 

Assembling the Backguard

It is mandatory to install the backguard.

Assemble the backguard as shown in figure 1.3:

  • Screw the 2 screws “A” interposing the spacers.

  • Screw the central screw “B”.

Screen Shot 2018-01-08 at 12.34.54 PM.png

Proximity to side cabinets - Standard Installation

fixed42_720.png

Reference Inch mm
A 0" 0
B 36" 914
C 11” 13/16 300
D 30" minimum 762 minimum
E 18" minimum 457 minimum
F 13" maximum 330 maximum
G 20" minimum 500 minimum

Proximity to side cabinets - Island Installation

 

 

fig1.5a.PNG

 

 

Reference Inch mm
A 0" 0
B 36" 914
C 11” 13/16 300
D 30" minimum 762 minimum
E 18" minimum 457 minimum
F 13" maximum 330 maximum
G 20" minimum 500 minimum
H 12" minimum 305 minimum

 

Screen Shot 2018-01-08 at 12.54.09 PM.png

Leveling the Range

The range is equipped with 4 LEVELING FEET and may be leveled by screwing or unscrewing the feet ( figs. 1.6 - 1.7).
It is important to observe the directions in figures 1.6, 1.8a, 1.8b.

Screen Shot 2018-01-08 at 12.54.39 PM.png


Screen Shot 2018-01-08 at 12.55.15 PM.png

Screen Shot 2018-01-08 at 12.55.50 PM.png

Anti-tip stability device installation instructions

You MUST use stability Anti-tip bracket to prevent unit from tipping.

  1. The anti-tip bracket has to be attached as shown on figure below (only rear left side), it has to be fixed on the floor OR on the rear wall by no. 4 (four) suitable screws (not supplied). Alternatively the anti-tip bracket can also be fixed on the floor AND on the rear wall by no. 8 (eight) suitable screws (not supplied).
  2. After fixing the anti-tip bracket, slide range into place. Be sure the rear left foot slides under the anti-tip bracket attached.

Screen Shot 2018-01-08 at 1.00.18 PM.png

Installing the Cooktop front guard

To increase the clearance between the front edge of the cooktop and the burners it is possible to install the cooktop front guard supplied with the appliance.

 

IMPORTANT: To install/remove the guard it is necessary to remove the cooktop.
Attempting to install/remove the guard without disassembling the cooktop will result in permanent damage to the appliance
.

Install the front guard as shown in figure 1.10:

  1. Remove the backguard.
  2. Remove the pan supports, the burner caps and flame spreaders.
  3. Unscrew cooktop fixing screws (“A” in figure below).
  4. Remove the dual burner inner flame spreader (“B” in figure below).
  5. Remove the cooktop (keep attention not to damage the gaskets fitted above the burner cups - below the cooktop).
  6. Install the front guard “C” by inserting the wire terminals into the proper holes above the control panel (“D” in figure below).
  7. Reassemble the cooktop and the other components (steps from 5 to 1).
    Pay special attention to the gaskets fitted above the burner cups (below the cooktop); if they are damaged they shall be replaced.

fixed44_720.png

 

  • Was this article helpful?