Skip to main content
Fisher & Paykel Product Help

Door Panel Installation - Stainless Steel or Custom

 

 

Stainless Steel

Door Handle Kit

M5x25 Hex Screw.PNG

M5x25 Hex screw (4x)

 

Door Panel Attachment Kit

Side Bracket.PNG

Side bracket (6)

Bracket Slider.PNG

Bracket slider (6)

Bracket Spacer.PNG

Bracket spacer (6)

8Gx16 Mush Washer Screw for SS.PNG

8Gx16 Mush washer screw (30)

 

Tools

Power Driver.PNG

Powered driver
(with 2.5mm drill bit)

M4 Hex Key.PNG

M4 hex key (1)

Spanner 13mm.PNG

13mm spanner (1)

  • Ensure to protect the finish of the Fisher & Paykel Stainless Steel door panels.

  • Leave the protective film on the panels when hanging and remove the film only when the installation is complete.

 

Remove Hanging Bracket

  1. Remove the M8 washer and M8 nut from the M8 screws at the top the door (A) using the supplied hex key and spanner.
Remove Hanging Bracket_A&C.PNG
  1. Remove the hanging bracket from the top of the door and set aside (B).

  2. Unscrew the adjustment screws by 3mm to move close to the middle of adjustment range (C).

 

Remove Hanging Bracket_B.PNG

 

Attach the Door Handle

  1. Remove the plastic plugs from handle holes (x4).

  2. Align the handle to the holes and secure with M5x25 hex screws (D).

 

Attach the Hanging and Side Brackets

  1. Align the screw holes of the hanging bracket with the screw holes of the door panel, and fix with 8Gx16 mush washer screws (E).

    • 6x screws for 457mm

    • 10x screws for 610mm and 762mm

  2. Align the side panel bracket assembly (bracket, slider and spacer) to the screw holes on the side of the door panel and fix with 8Gx16 mush washer screws (F).

Remove Hanging Bracket_D.PNG

Remove Hanging Bracket_D&E&F.PNG

 

Tools

Cross Head Screwdriver.PNG

Cross-head screwdriver

Power Driver.PNG

Powered driver
(with 2.5mm drill bit)

M4 Hex Key.PNG

M4 hex key (1)

Spanner 13mm.PNG

13mm spanner (1)

 

Hang the Door Panel

  1. Remove the gauges and retighten the screws. Open the door and loosen the screws at both sides of the door (do not remove) (A).
  2. Hang the door panel with a small angle to the door by locating the holes of the top bracket to the M8 studs (B), and rotate the door panel down so that the side attachment brackets slide onto the side screws of the door. (C)
  3. Screw the M8 washer and nut to the stud (D), and re-tighten the side screws (A) to fix the door panel (do not fully tighten). This will allow opening the door without affecting adjustment of the door panel.

 

We recommended to load the shelves in the product door with weights to ensure an accurate door panel gap width.

Weight recommendations:

  • 57mm product: 10kg
  • 610mm product: 15kg
  • 762mm product: 20kg

 

Adjust the Door Panel

Check the gaps between door panel/cabinetry using the gauge (3mm). All door panels have full axis adjustment to ensure they are flush with adjacent walls.
  1. To adjust the height of the door panel relative to the door, use M4 hex key to turn the top M8 screw (E) clockwise to lower or counter-clockwise to raise the door panel until the gap with the cabinetry above is 3mm.
  2. To adjust the depth of the door panel, loosen the side screws (F) from each side and slide the panel forward/ backward. Re-tighten once satisfied.
  3. To adjust the door panels further, remove the door panels then loosen the fixing screws for the hanging bracket and move the bracket sideways to suit. (G)
  4. Once satisfied with the door panel position, fully tighten M8 washer and nut to the stud using the supplied hex key and spanner (E).

 

Fix the Locking Brackets

  1. Loosen the screw at the bottom of the door, and slide the locking bracket out until it touches the panel (H).
  2. Fix the locking bracket to the door panel with 8Gx16 countersunk screw (I).
  3. Re-tighten the screw at the bottom of door (J).
Door Panel Installation SS.PNG

 

Custom

Door Handle Kit

M5x25 Hex Screw.PNG

M5x25 Hex screw (4x)

 

Door Panel Attachment Kit

Side Bracket.PNG

Side bracket (6)​​​​​​​

Bracket Slider.PNG

Bracket slider (6)​​​​​​​

Bracket Spacer.PNG

Bracket spacer (6)​​​​​​​

M5x12 Cross Head Screw.PNG

M5x12 Cross-head screw (30)​​​​​​​

  • Ensure the screw pilot holes do not penetrate the full depth of the panel.
  • Do not place the handle holes in marked areas to avoid clashing with panel attachment brackets.
  • Minimum panel thickness where screw hole is drilled must be 16mm.

Remove Hanging Bracket

  1. Remove the M8 washer and M8 nut from the M8 screws at the top the door (A) using the supplied hex key and spanner.

Remove Hanging Bracket Custom_A&C.PNG

 

  1. Remove the M8 washer and M8 nut from the M8 screws at the top the door (B).
  2. Unscrew the adjustment screws by 3mm to move close to the middle of adjustment range (C).
  3. Mark the location of the screw holes and drill pilot holes to the marked location. Refer to the custom panel template in the ‘Custom door panel dimensions’ section.

Remove Hanging Bracket Custom_B.PNG

 

Attach the Door Handle

  1. Fix the handle with M5x25 hex screws from the inner edge of the panel (D). Refer to ‘Custom door panel dimensions’ section to ensure door handle does not interfere with side attachment brackets.

 

Attach the Hanging and Side Brackets

  1. Mark the centreline from the top of the Custom panel and align with the ‘V’ notch in the bracket (E).
  2. Align the screw holes of the bracket with the screw holes of the door panel and fix the hanging bracket to the door panel with M5x12 Cross-head screws (F). – 6 screws for 457mm – 10 screws for 610mm and 762mm
  3. Align the side panel bracket assembly (bracket, slider and spacer) to the screw holes on the side of the door panel and fix with 8Gx16 mush washer screws (G).

Remove Hanging Bracket Custom_D.PNG

Remove Hanging Bracket Custom_EtoG.PNG

 

Tools

Cross Head Screwdriver.PNG

Cross-head screwdriver​​​​​​​

Power Driver.PNG

Powered driver/drill (with 2.5mm bit)​​​​​​​

M4 Hex Key.PNG

M4 Hex key (1)​​​​​​​

Spanner 13mm.PNG​​​​​​​

13mm spanner (1)

 

  • If using Custom door panels, ensure they are prepared as per ‘Custom door panel dimensions’ section.

 

Hang the Door Panel

  1. Remove the gauges and retighten the screws. Open the door and loosen the screws at both sides of the door (do not remove) (A).
  2. Hang the door panel with a small angle to the door by locating the holes of the top bracket to the M8 studs (B), and rotate the door panel down so that the side attachment brackets slide onto the side screws of the door. (C)
  3. Screw the M8 washer and nut to the stud (D), and re-tighten the side screws (A) to fix the door panel (do not fully tighten). This will allow opening the door without affecting adjustment of the door panel.
We recommended to load the shelves in the product door with weights to ensure an accurate door panel gap width.

Weight recommendations:

  • 457mm product: 10kg
  • 610mm product: 15kg
  • 762mm product: 20kg

 

Adjust the Door Panel

Check the gaps between door panel/cabinetry using the gauge (3mm). All door panels have full axis adjustment to ensure they are flush with adjacent walls.
  1. To adjust the height of the door panel relative to the door, use M4 hex key to turn the top M8 screw (E) clockwise to lower or counter-clockwise to raise the door panel until the gap with the cabinetry above is 3mm.
  2. To adjust the depth of the door panel, loosen the side  screws (F) from each side and slide the panel forward/backward.  Re-tighten once satisfied.
  3. To adjust the door panels further, remove the door panels then loosen the fixing screws for the hanging bracket and move the bracket sideways to suit. (G)
  4. Once satisfied with the door panel position, fully tighten M8 washer and nut to the stud using a M4 hex key (E).

 

Fix the Locking Brackets

  1. Loosen the screw at the bottom of the door, and slide the locking bracket out until it touches the panel (H).
  2. Fix the locking bracket to the door panel with 8Gx16 countersunk screw (I).
  3. Re-tighten the screw at the bottom of door (J).

Door Panel Installation Custom.PNG​​​​​​​

 

 

 

  • Was this article helpful?