Skip to main content
Fisher & Paykel Product Help

Installation instructions

Please read and follow the ‘Safety and warnings’ and ‘installation instructions’ sections carefully before using your rangehood.
 

Contents of packaging

Rangehood (1)

Installation instructions User guide manual (1)

125 mm ducting adapter with non return flap (1)

13 mm screw (2)

 

Product and cabinetry cutout dimensions

Product Dimensions

Property (mm)

HP60ICSX2

HP90ICSX2

  1. Overall height of product (with ducting adapter)

260
(330)

260
(330)

  1. Overall width of product

492

792

  1. Overall depth of product

277 277
  1. Thickness of flange

1 1
  1. Width of chassis

450 750
  1. Depth of chassis

255 255
  1. Height of side of chassis

N/A 100
  1. Width of top surface of chassis

267 250
  1. Length of angled surface of chassis

276 273
  1. Distance from centre of ducting outlet to back of chassis

73 73
  1. Distance from centre of ducting outlet to side of chassis

225 375
  1. Diameter of ducting outlet

125 125
  1. Distance between centre of lights

340 385
  1. Distance from centre of light to front of product

45 45

Length of power cord

950 950

 

Cabinetry Cutout Dimensions

Property (mm)

HP60ICSX2

HP90ICSX2

Overall width of cutout

460 760

Overall depth of cutout

260 260
  1. Base of brackets/clips to bottom of chassis

min. 15 – max. 35

min. 15 – max. 35

Actual product dimensions may vary by ± 2 mm.

Please read the entire instructions before installing the rangehood.

Height of rangehood 

Minimum Clearances

Property

Size (mm)

  1. Height top of cooktop to base of product
    Electric cooktop
    Gas cooktop

min. 600 – max. 750
min. 650 – max. 750

Rangehood installation height above the cooktop is the user’s preference. Lower installation heights will improve the efficiency of capturing cooking odours, grease, and smoke. This rangehood must be installed between the minimum and maximum dimensions indicated in the table above.

Venting options

Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled.

The rangehood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to operate with the exhaust air recirculating within the kitchen.

Ducted

For ducted installation it is recommended that 125 mm diameter, rigid or semi-rigid ducting is used. This will require a 135 mm (min) round hole in the ceiling or wall. Care should be taken to position the hole correctly.

For optimal efficiency use the shortest and straightest duct route possible and use rigid or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting should only be used as a last resort (ie in difficult installations) and if used ensure that it is straight and smooth and extended as much as possible.

Recirculating

Where ducting outside is not a practical option, this rangehood can be installed to operate with the air recirculating. Carbon filters are required to remove odours from the air before it is channelled back into the room or overhead bulkhead (refer to ‘Parts and accessories’ section). Ensure that the ducting outlet is not obstructed, even a partial obstruction will restrict the efficiency of the rangehood.

  • This appliance is heavy and requires two persons for unpacking and installation
  • Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards.
  • Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards

Wear gloves to protect against sharp edges.

The manufacturer is not liable for any damage caused by not following these instructions.

Installation

  1. Prepare for installation.
    Before installing your rangehood:

  • Please read the instructions carefully.
  • Unpack the rangehood and check that all functions are working.
  • Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency at the installation site.
  • The stainless steel and glass surfaces of the rangehood are very easily damaged during installation if grazed or knocked by tools. Please take care to protect the surfaces during installation.
  • Protect the cooktop surface below with cardboard, or the like, to prevent damage occurring whilst the rangehood is being installed above.
  1. Fit the 125 mm ducting adapter with non return flap to the rangehood using the screws supplied.

  2. Provide an opening on the underside of the cupboard (see 'Product and cabinetry cutout dimensions').

  1. Remove the filter from the rangehood.

  1. Connect duct and plug rangehood in.

  1. Lift the rangehood and fit through the opening of the cupboard till the spring loaded brackets / clips hold the product in place.

  1. Secure rangehood while tightening the 2 brackets / clips.

  • Was this article helpful?