Skip to main content
Fisher & Paykel Product Help

Care and cleaning

 

Before you start cleaning your cooker, please:

  • Read these cleaning instructions and the ‘Safety and warnings’ section at the start of this user guide.
  • Turn the cooker off at the wall.
  • Make sure the cooker is a safe temperature to touch.
  • Do not use a steam cleaner.
  • Do not keep flammable substances in the oven.

General advice

  • Wipe down the cooktop and wipe out the oven after every use.
  • Wipe up spills. Avoid leaving alkaline or acidic substances (such as lemon juice or vinegar) on the surfaces.
  • Do not use cleaning products with a chlorine or acidic base.

Cleaning the outside of the cooker

  • Do not use abrasive cleaners, cloths or pads on the outside surfaces.
  • Immediately wipe off any caustic cleaners if they are spilled onto the oven door handle.

Wipe the outside surfaces often, using warm water and a mild household detergent. The stainless steel may also be cleaned with a suitable cleaner and polish.

If you choose to use a commercial stainless steel cleaner, please read the label to make sure it does not contain chlorine compounds as these are corrosive and may damage the appearance of your cooker.

Cleaning the gas cooktop

Maintenance Period

Description

Daily

  • Clean gas cooktop as per following instructions.

Monthly

  • Remove all burner parts, and clean using a non-abrasive detergent. Rinse in cold water, dry thoroughly, and replace.
  • Clean the ignitor carefully, using a toothbrush and methylated spirits.

Every 3-4 years

  • Contact your local authorised gas Service Agent to perform a thorough check on all gas components on the gas cooker.

 Burner parts and pan supports

  • You can remove and clean these parts with hot soapy water or non-abrasive detergents. Clean spills regularly before they become burnt on. Do not wash these parts in a dishwasher.
  • After cleaning, check that the burners and their flame spreaders are dry before replacing correctly.
  • It is very important to check that the burner flame spreader and the cap have been correctly positioned. Failure to do so can cause serious problems.

To avoid damage to the electronic ignition, do not try to light a burner without all burner parts in place

Replacing the semi-rapid burners

  • Carefully replace the burner parts as per the following Figs. Check that:
  • the ignitor is always clean to ensure trouble-free sparking.
  • the probe is always clean to ensure correct operation of the safety valves (some models only) Note: both the ignitor and probe must be very carefully cleaned using a toothbrush and methylated spirits (see Fig.26).

 

Fig. 30 Correct line-up of semi-rapid burner parts

Fig. 31 Replacing the semi-rapid burner caps

Replacing the triple-ring wok and dual burners

  • Carefully replace the burner parts as per the following Figs.
  • Fit the flame spreader to the housing as shown by the arrow in the Figs.32a-32b. Make sure the burner is not able to rotate (Fig. 33).

Check that:

  • the ignitor is always clean to ensure trouble-free sparking.
  • The probe is always clean to ensure correct operation of the safety valves (some models only)

Both the ignitor and probe must be very carefully cleaned using a toothbrush and methylated spirits (see Fig.26).

Fig. 32a Correct positioning of flame spreader - triple-ring wok burner

Fig. 32b Correct positioning of flame spreader - dual burner

Fig. 33 Correct positioning of cap and ring - triple-ring wok and dual burner

Fig. 34 Incorrect and correct positioning of cap and ring - triple-ring wok and dual burner

 Cleaning the inside of your oven

If using the Self Clean function remove all shelves and side racks first. See ‘Using the Self Clean function’.

  • Do not use abrasive cleaners, cloths or pads to clean the enamel.

Removing the side racks

  1. Using a small coin or a flat-head screwdriver, loosen and remove the front fixing screw.
  2. Slide the side rack clear of the rear lock stud and remove.

Refitting the side racks

  1. Slide the side rack gently so it engages with the rear lock stud. Make sure that they are the right way up, as in the illustrations, and then insert and tighten the front fixing screw.
  2. If not already fitted, fit the telescopic sliding shelf supports. See “Care and cleaning’ for instructions.

 

Fig. 35 Removing the side racks

 

Cleaning the enamel cavity

Clean the enamel on the inside of the oven when it has cooled down, using household detergents. You may use ‘off the shelf’ oven cleaners, if you carefully follow the manufacturers’ instructions.

Cleaning the grill tray and shelves

Clean these in hot, soapy water.
After cleaning slide in the shelves, making sure that:

  • they are between the two wires of a shelf position;
  • the stop notches point down;
  • the guard rail is at the back.

The grill tray should be positioned between the two wires of a shelf position and orientated as shown.


Fig. 36 Oven shelves and grill tray

Fitting and removing the sliding shelf supports

When fitting the sliding shelf supports, make sure that you fit:

  • the side racks
  • the slides to the top wire of a shelf position
  • both sides of each pair of slides
  • both slides on the same level.

Remove the side racks first to make removing the sliding shelf supports easier.

Fig. 37a Fitting the sliding shelf supports

Fig. 37b Removing the sliding shelf supports

Storage Drawer

  • The drawer opens like a normal drawer. The drawer slides prevent the drawer from sliding out.

To remove the drawer

  1. Open the drawer fully.
  2. Press the lever on the left guide rail down and the right guide rail up.
  3. Holding the levers, disengage and remove the drawer. Do not use excessive force or you may damage the drawer slides.

Fig. 38 Removing the drawer

Replace the drawer

  1. Insert the drawer rails into the guide rails.
  2. Gently push the drawer in completely, the catches will automatically hook.

Fig. 39 Replacing the drawer

Replacing the oven light bulbs

The oven light bulbs (12V/20 W halogen) have a very long life, but if you should need to replace one, use only a replacement bulb purchased from your nearest Fisher & Paykel dealer and follow these steps.

Oven bulb replacement is not covered by your warranty.. 

1. Allow the oven to cool down, then turn it off at the mains power supply (wall switch).

2. Remove any oven shelves that may get in the way.

3. Using a flat-head screwdriver, twist and lift the retainer clip upwards to release the glass cover. Hold the glass cover to prevent it falling.

4. Carefully lift the glass cover out of the retaining bracket in the back and pull out the faulty bulb.

5. Hold the replacement bulb in a soft cloth or tissue (touching the bulb will reduce its life span) and insert it into the socket.

6a. Reposition the glass cover and twist the retainer clip back in place.

6b .Turn the oven back on at the mains power supply (wall switch).

Removing and replacing the door glass panes for cleaning.

Make sure you follow the precautions and instructions below very carefully. Replacing the glass panes and the door incorrectly may result in damage to the oven and may void your warranty.

Your oven door has 4 panes of glass. The inner and middle panes may be removed for cleaning.

  • Switch the oven off at the wall before removing the door.
  • Take care, the oven door is heavy. If you have any doubts, do not attempt to remove the door. Make sure the oven and all its parts have cooled down. Do not attempt to handle the parts of a hot oven.
  • Take extreme care when handling the glass panes. Avoid the edges of the glass bumping against any surface. This may result in the glass shattering.
  • Don’t use oven cleaners or any other harsh/abrasive cleaners, cloths, scouring pads, steel wool or sharp metal scrapers to clean the glass surfaces. These scratch the glass and may damage its special coating, which in turn could result in the glass cracking or shattering.
  • If you notice any sign of damage on any of the glass panes (such as chipping or cracks), do not use the oven. Call your Authorised Repairer or Customer Care.
  • Make sure you replace all the glass panes correctly. Do not use the oven without all glass panes correctly in place.
  • If the glass panes feel difficult to remove or replace, do not force them. Call your Authorised Repairer or Customer Care for help.

Service visits providing assistance with using or maintaining the oven are not covered by your warranty.

Removing the door

1a.  Turn the oven off at the wall. Make sure you have prepared enough space for resting the door and its glass panes on a clean, flat surface.

1b.  Open the door to its full extent.

2. Open the levers on the left and right hinges to their full extent, as shown.

3. Gently close the door until the left and right hinge levers are hooked to the door.

4. Hold the door firmly, as shown.

5a.  Lift the door and disengage the hinges.

5b.  Rest the door on a soft surface. Ensure you lay it with the handle side down.

 

Remove the inner and middle glass panes

1. Press down on both tabs (1) to release the glass retainer (2).

2. Lift the inner pane (D) slightly (1), then gently slide out (2).

3. Slide the first middle pane (C) slightly towards yourself (1), then lift (2) and slide out (3).

4. Slide the second middle pane (B) slightly towards yourself (1), then lift (2) and slide out (3).

After cleaning, replace the glass panes

When replacing the glass panes, make sure that:

  • you replace all three panes correctly, as shown. Each pane must be in the position described below in order to fit into the door and to ensure that the oven operates safely and correctly.
  • you take extra care not to bump the edges of the glass against any object or surface.
  • you do not force any of the panes into place. If you are experiencing difficulties replacing the panes, remove them and start the process again from the beginning. If this still does not help, call Customer Care.

The two middle panes (B and C) are identical.

  1. Take the middle pane (B) and hold it firmly. Insert it in the lowest pair of grooves (1), push it slightly towards yourself (2) and gently lower into place (3).

  1. Take the other middle pane (C) and hold it firmly. Insert it in the next pair of grooves (1), push it slightly towards yourself (2) and gently lower into place (3).

  1. Take the inner pane (D), holding it with the angle-cut corner orientated as shown. Insert it in the uppermost pair of grooves (1), push it slightly towards yourself (2) and gently lower into place (3).

Make sure that the angle-cut corner of the inner pane (D) is at the bottom of the oven door, on the left-hand side. It has to be in this position for the door to function correctly.


  1. Position the glass retainer, as shown. It should sit on the bottom edge of the outer glass (A). Check that the clamps of the glass retainer are not deformed or damaged.


  1. Gently push the glass retainer back into place. You should be able to hear the tabs on both sides click as they lock the glass retainer in.

Make sure the glass retainer is correctly and firmly in place and that the glass panes are secure.

Refit the door

1. Hold the door firmly.

2. Insert the hinge tongues into the slots, making sure that the notches on both sides drop into place as shown.

3. Open the door to its full extent.

4a. Fully close the levers on the left and right hinges, as shown.

4b. Close the door, turn the power supply to the oven on at the wall.

 

  1. Check the door shuts completely and that the door lock (at top centre of door) is not obstructing the door.
  2. Check the door sensor (top left) is correctly operating:
    • start a ‘Self Clean’ cycle (see ‘Using the Self clean function’)
    • wait five minutes - the door lock indicator light should turn on.
    • after five minutes turn the function dial to O (Off ).

Do not continue with the Self Clean cycle if the side racks or shelves are in the oven.

 

If the door lock indicator light does not turn on, or the display shows refer to ‘Troubleshooting’.

  • Was this article helpful?