Skip to main content
Fisher & Paykel Product Help

Safety and Warnings

Read these instructions carefully before installing this product.

WARNING!

Electrical shock hazard

  • Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply.
  • Connection to a good earth wiring system is absolutely essential and mandatory.
  • Alterations to the domestic wiring system must only be made by a qualified electrician.
  • Failure to follow this advice may result in electrical shock or death.

Cut hazard

  • Take care - some panel edges are sharp.
  • Failure to use caution could result in injury or cuts.

 

Important Safety Instructions!

  • Particular attention shall be given to the relevant requirements regarding ventilation.
  • Read these instructions carefully before installing this product.
  • Please make this information available to the person installing the appliance as it could reduce your installation costs.
  • This appliance is to be installed and serviced only by an authorised person.
  • Installation must comply with your local building and local gas authority codes and electricity regulations.
  • Incorrect installation, for which the manufacturer accepts no responsibility, may cause personal injury or damage and could invalidate any warranty or liability claims.
  • These appliances are registered in: (New Zealand) at www.energysafety.govt.nz and (Australia) with SAI Global at www.saiglobal.com.
  • Appliances are factory set for Natural gas but are convertible to LPG. If in doubt, refer to the local gas network operator or gas supplier to confirm gas type at installation site.
  • Do not modify this appliance.
  • Do not use or store flammable materials on or near this appliance.
  • Do not spray aerosols in the vicinity of this appliance while it is in operation.
  • Packing elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as these may cause serious injuries.

Before you install the appliance, please make sure that

  • the local distribution conditions (nature of gas and pressure) and the adjustment of the appliance are compatible. For adjustment conditions for this appliance see ‘Gas rate summary’.
  • a suitable disconnection switch is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations. A means of disconnection with at least a 3 mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules, unless the local wiring rules allow for alternative means.
  • the appliance is connected to a 220V - 240V 50Hz (10 A) power supply only and earthed via the power supply cable.
  • there is a power outlet within reach of the power supply cable (900 mm from the centre rear of the product). This must be accessible after installation. The power supply cable should not touch any metal parts.
  • if the power supply cable is damaged, it is replaced only by the special cable: Part no. 534050 - Flex Terminal Block Assy NZ/AU, obtainable from authorised Fisher & Paykel Service Agents.
  • the supply connection point (gas shut-off valve) is accessible after installation.
  • the benchtop is made of a heat resistant material.
  • the installation complies with all the requirements of Australian and New Zealand Gas Installation Standards (AS/NZS 5601.1.2010), including that the product has to be installed so that the surface temperature of any nearby combustible surface will not exceed 65 OC above ambient. See ‘Clearance Dimensions’.

When you install the appliance

  • We do not recommend you seal this appliance into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for any costs associated with removing or replacing a sealed-in appliance, nor for repairing any damage that may be incurred by doing this.
  • If installed with an approved flexible hose, the hose should not come in contact with the bottom of the appliance or any sharp edges. Flexible hose assemblies should be AS/NZS 1869 Class B or Class D certified.
  • Seal exposed bare edges of the cutout with an oil-based paint or moisture-proof polyurethane to prevent possible moisture creeping between the cooktop trim and the benchtop.
  • If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through our local website listed at the end of this document.
  • Was this article helpful?