Skip to main content
Fisher & Paykel Product Help

Cabinetry Dimensions

Underbench (IE Installed With a F&P 60cm Wide Single Oven)


* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.

** In some instances the front cabinetry rail may need to be removed to enable installation. 

Property

Size (mm)

  1. Minimum inside height of cavity (with F&P 60cm wide single oven)

687

  1. Inside width of cavity

560

  1. Minimum inside depth of cavity

565

When installed in combination with a companion product the companion product may be placed directly onto the warming drawer. It is not necessary to place a shelf between the products. A built-in shelf at the base of the cabinetry able to support the weight of both products is required.  

If Installing under an oven, you must first fit the two supplied Oven support brackets to the sides of the Warming Drawer. The brackets help support the rear of the oven. Unscrew the 3 top screws on each side, fit the brackets with the tabs facing inwards as shown and screw back in. 
The screws may not be identical. Replace each screw into its original hole position.

Wall mounted (IE Installed With a F&P Compact Oven)

In a wall mounted installation, there needs to be an 18 mm Spacer fixed underneath the warming drawer first to raise it to the required height.

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product.

Property

Size (mm)

  1. Minimum inside height of cavity with optional Lower trim kit fitted without optional Lower trim kit fitted

590
570

  1. Inside width of cavity

560

  1. Minimum inside depth of cavity

565

 When installed in combination with a companion product the companion product may be placed directly onto the warming drawer. It is not necessary to place a shelf between the products. A built-in shelf at the base of the cabinetry able to support the weight of both products is required.  

Wall mounted (IE Installed With a F&P Coffee Maker)

If installing under the F&P Coffee Maker, ensure there is the 45mm gap at the back of the cabinet and the 200mm² toekick cutout required for airflow.
Refer to the Coffee Maker Install instructions.


 

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product 

  • If installing under the F&P Coffee Maker, ensure there is the 45mm gap at the back of the cabinet and the 200mm2 toekick cutout required for airflow. Refer to the Coffee Maker Install instructions.
  • When installing under an F&P Coffee Maker you must ensure the supplied anti-tip bracket is installed, unless there is a fixed shelf above the drawer acting as an anti-tip obstacle.
  • In a wall mounted installation, there needs to be an 18mm Spacer fixed underneath the warming drawer first to raise it to the required height. 

Property

Size (mm)

  1. Minimum inside height of cavity with optional Lower trim kit fitted without optional Lower trim kit fitted

590
570

  1. Inside width of cavity

560

  1. Minimum inside depth of cavity

565

When installed in combination with a companion product the companion product may be placed directly onto the warming drawer. It is not necessary to place a shelf between the products. A built- in shelf at the base of the cabinetry able to support the weight of both products is required.

Wall mounted (Standalone)


 

* PO - POWER OUTLET. Ensure there is an accessible earthed power outlet within 900mm of the centre rear of the product 

  • In a standalone wall mounted installation, you must ensure that the supplied anti-tip bracket is installed unless there is a fixed shelf above acting as an anti-tip obstacle.
  • In a wall mounted installation, there needs to be an 18mm Spacer fixed underneath the warming drawer first to raise it to the required height.

Property

Size (mm)

  1. Inside height of cavity

120

  1. Inside width of cavity

560

  1. Minimum inside depth of cavity

545

  • Was this article helpful?