Skip to main content
Fisher & Paykel Product Help

Installation Method

Now choose which installation method (A) OR (B) is more suitable for your cabinetry.

Now choose which installation method (A) OR (B) is more suitable for your cabinetry...

2017-08-04_1221.png


1-A. Attach side mounting brackets

Clip all four side mounting brackets into their slots using a flat-bladed screwdriver. Ensure they’re securely fitted before sliding product into cavity.

2017-08-04_1218-fixed.png

The mounting slots are in pairs, one on each side diagonally across the product. A bracket must match A slot and B bracket must match B slot.

2-A. Pull through hoses & push into the cavity

2017-08-04_1219.png

3-A. Secure the cabinetry on the sides

2017-08-04_1227.png

4-A. Optionally secure to the cabinetry above

The top mounting brackets will only bend upwards a maximum of 10mm.

2017-08-04_1228-fixed.png

5-A. Fit the supplied toekick panel (Optional for integrated models)

Where the toekick meets the bottom of the tub is the cut-off point

2017-08-04_1235-fixed1.png

Mark this point on the toekick with a pencil

2017-08-04_1235-fixed3.png

Lay the toekick face down on a chopping board or similiar

2017-08-04_1235-fixed4.png

Score along with a knife

2017-08-04_1235-fixed5.png

Turn the toekick over and score along the same line

2017-08-04_1235-fixed6.png

Gently snap off the excess

2017-08-04_1235-fixed7.png

Smooth the edge with a file.

Be careful of sharp edges.

2017-08-04_1235-fixed8.png

Snap off the two end tabs

Slide the toekick onto the mounting rails either side and screw the toekick onto the bottom of tub on either side.

 2017-08-04_1235-fixed9.png

Important-Icon.png

Do not overtighten screw.

Alternative method (B) - Secure by drawer removal

2017-08-04_1355.png

1-B. Pull through hoses & push into the cavity

2017-08-04_1357.png

2-B. Remove the lower drawer

2017-08-04_1359.png

Press the release tabs in on either side and push back to release drawer from runners.

To prevent kinked hoses, we recommend rotating the drawer anti-clockwise and resting it on its side after removal.

2017-08-04_1401-fixed.jpg

Push drawer runners back in.

3-B. Secure to the cabinetry on the sides

2017-08-04_1402.png

 

4-B. Optionally secure to the cabinetry above

The top mounting brackets will only bend upwards a maximum of 10mm.

2017-08-04_1403_480-fixed.jpg

5-B. Refit the drawer onto the runners

2017-08-04_1405.png

6-B. Fit the supplied toekick panel (Optional for integrated models)

Where the toekick meets the bottom of the tub is the cut-off point

2017-08-04_1235-fixed1.png
Mark this point on the toekick with a pencil

2017-08-04_1235-fixed3.png

Lay the toekick face down on a chopping board or similiar

2017-08-04_1235-fixed4.png

Score along with a knife

2017-08-04_1235-fixed5.png

Turn the toekick over and score along the same line

2017-08-04_1235-fixed6.png
Gently snap off the excess

2017-08-04_1235-fixed7.png

Smooth the edge with a file.

Be careful of sharp edges.

2017-08-04_1235-fixed8.png

Snap off the two end tabs

Slide the toekick onto the mounting rails either side and screw the toekick onto the bottom of tub on either side.

2017-08-04_1235-fixed9.png 

Important-Icon.png

Do not overtighten screw. 

  • Was this article helpful?