Skip to main content
Fisher & Paykel Product Help

Installation instructions

Details the various product and cabinetry dimensions of your rangehood and everything else you need to need to know prior to installing your rangehood.

Contents of packaging

2017-09-27_1249.png
Rangehood hood (1)

2017-09-27_1250.png
Installation instructions User guide manual
(1)

2017-09-27_1251.png
Chimney (1)

2017-09-27_1251b.png
Upper chimney (1)

2017-09-27_1251c.png
Upper chimney bracket (1)

2017-09-27_1251d-fixed.png
Chimney bracket (1)

2017-09-27_1251e.png
150 mm diameter ducting adapter (1)

2017-09-27_1251f.png
Expansion plug (10)

2017-09-27_1251g.png
30 mm self-tapping screw (10)

2017-09-27_1251h.png
10 mm self-tapping screw (4)

 

Product dimensions

2017-09-27_1300.png
2017-09-27_1300-a.png 2017-09-27_1300-b.png
2017-09-27_1300-c.png 2017-09-27_1300-d.png 2017-09-27_1300-e.png

Product Dimensions

HC60PHTX1

HC90PHTX1

HC120PHTX1

A. Overall height of product (mm)

655 – 1094

655 – 1094

655 – 1094

B.  Overall width of product (mm)

598

898

1198

C.  Overall depth of product (mm)

500

500

500

D.  Height of product (mm)

113

113

113

E.  Width of chimney (mm)

320

320

320

F.  Depth of chimney (mm)

290

290

290

G.  Distance from centre of ducting outlet to back of product (mm)

95

95

95

H.  Distance from centre of ducting outlet to side of chimney (mm)

160

160

160

I. Diameter of ducting outlet (mm)

150

150

150

J.  Distance between centre of lights (mm)

1 light in centre N/A

2 lights on sides 820

3 lights (2 on sides, one in centre) 558

K.  Distance between lights to back of product (mm)

50 – 430

50 – 430

50 – 430

Length of power cord (mm)

800

800

800

Actual product dimensions may vary by ± 2 mm.

Please read the entire instructions before installing the rangehood.

Height of rangehood

2017-09-27_1453.png

Installation Dimensions mm

L. Installation height

  • Ducted
  • Recirculation

min. 680 – max. 1094
min. 720 – max. 1094

H. Height top of cooktop to base of product

min. 660 – max. 750

  • Rangehood installation height above the cooktop is the user’s preference.
  • Lower installation heights will improve the efficiency of capturing cooking odours, grease, and smoke. This rangehood must be installed between the minimum and maximum dimensions indicated in the table above.

Venting options

Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled.

The rangehood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to operate with the exhaust air recirculating within the kitchen.

Ducted

For ducted installation it is recommended that 150 mm diameter, rigid or semi-rigid ducting is used. This will require a 160 mm (min) round hole in the ceiling or wall. Care should be taken to position the hole correctly.

For optimal efficiency use the shortest and straightest duct route possible and use rigid or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting should only be used as a last resort (ie in difficult installations) and if used ensure that it is straight and smooth and extended as much as possible.

Recirculating

To enable the product to operate with the air recirculating, please purchase a recirculation diverter and carbon filters (refer to the ‘Parts and accessories’ section). This recirculation diverter is installed after a short length of ducting and is required to channel the air out the side vents at the top of the chimney and the carbon filters are required to remove odours.

A ducting hole is not required in the wall or ceiling if the rangehood is installed to operate with exhaust air recirculating.

Installation

  • This appliance is heavy and requires two persons for unpacking and installation

  • Installation work and electrical wiring must be done by qualified person(s) in

    accordance with all applicable codes and standards.

  • Failure to install the screws or fixing device in accordance with these instructions

    may result in electrical hazards.

  • Wear gloves to protect against sharp edges.

  • The manufacturer is not liable for any damage caused by not following these instructions.

  1. Preparing for installation:
    Before installing your rangehood:

  • Please read the instructions carefully.
  • Unpack the rangehood.
  • Ensure the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency of the installation site.
  • Check all functions are working.
  • Check that the area behind the installation surface to be drilled is clear of any electrical cables or pipes etc.
  • The rangehood surfaces can be damaged during installation if grazed or knocked by tools. Please take care to protect the surfaces during installation.
  • Protect the cooktop surface with cardboard, or the like, to prevent damage occurring whilst the rangehood is being installed above.
  • Temporarily mark the height of the bottom of the rangehood and the centre of the cooktop on the wall according to the information given in the ‘Installation instructions – Height of rangehood’ section.
  • The wall used for mounting the rangehood should have sufficient strength and a flat surface.
  1. Attach chimney brackets and rangehood mounting screws to the wall
  • Attach the chimney bracket and upper chimney bracket (if using the upper chimney) in the locations shown in Fig. 2 and 3. Use the 30 mm screws (and expansion plugs if attaching to masonry).
  • Attach the upper rangehood mounting screws in the locations shown in Fig. 2 and 3. Using the 30 mm screws (and expansion plugs if attaching to masonry). Ensure that there is a 2 mm gap between the screw head and the wall (see Fig 1).

2017-09-27_1327.png

2017-09-27_1507.png 

Product Dimensions mm

N. Lower rangehood attachment point width

508

O. Lower rangehood attachment point height

44

P. Upper rangehood attachment point width

250

Q. Upper rangehood attachment point height

291

R. Chimney bracket attachment point width

235

S. Chimney bracket attachment point height

615

T. Upper chimney bracket attachment point width

250

U. Upper chimney bracket attachment point height

25

2017-09-28_1031.png

  1. Attach the ducting adapter to the rangehood
  • Place the ducting adapter onto the rangehood and screw it in place using 10 mm screws.
2017-09-28_1032.png
  1. Wall mounting
  • Remove the filters – pull the relative catch and tilt the filter downwards until it disengages from the supports.

2017-09-28_1035.png

  • Hang the rangehood off the upper rangehood mounting screws with 2 mm gap. Hang off the keyhole attachment points on the back of the rangehood then tighten the screws.

2017-09-28_1036.png

  • Attach the lower rangehood mounting screws to fix the rangehood to the wall.
  • Refit the filters.
  1. Attach the ducting

  • Attach ducting to the ducting adapter using aluminium duct tape and vent outside.
  1. Attach chimney

  • Bend the tabs on the chimney (A).
  • Place chimney around the rangehood chassis and hang off the chimney bracket (B).
  • Extend the upper chimney and attach to the upper chimney bracket with 10 mm screws (C).
2017-09-28_1041.png 2017-09-28_1042.png 2017-09-28_1043.png
  1. Remove packaging

  • Remove all packaging and protective wrappings.
  • Was this article helpful?