Skip to main content
Fisher & Paykel Product Help

Displayed Messages

 

 

Displayed Message

Possible Cause What To Do

Displayed Mess_Fill Tank.PNG

FILL TANK WITH FRESH WATER

Insufficient water in the tank. Fill the tank with water and ensure that it is inserted correctly, pushing it as far as it will go until it clicks into place.

Displayed Mess_Insert Water Tank.PNG

INSERT WATER TANK

The tank is not correctly in place. Insert the tank correctly and press as far as it will go.

Displayed Mess_Empty Grounds Cont.PNG

EMPTY GROUNDS CONTAINER

The grounds container is full.

Empty the grounds container and drip tray, clean and place it back in the appliance.

When removing the drip tray, the grounds container must be emptied, even if it contains few grounds. If this is not done, when you make the next drinks, the grounds container may fill up more than expected and clog the machine.

Displayed Mess_Insert Grounds Cont&Drip Tray.PNG

INSERT GROUNDS CONTAINER AND DRIP TRAY

After cleaning, the grounds container has not been re-inserted. Remove the drip tray and insert the grounds container.

Displayed Mess_Add Pre Ground Coffee.PNG

ADD PRE-GROUND COFFEE, COFFEE MAX. 1 MEASURE

The ‘pre-ground coffee’ function has been selected without placing any pre-ground coffee in the funnel. Place pre-ground coffee in the funnel and repeat delivery
The pre-ground coffee funnel is clogged. Empty the funnel as described in section ‘Cleaning the pre-ground coffee funnel.’

Displayed Mess_Coffee.PNG

ADD COFFEE, COFFEE MAX. 1 MEASURE

A long coffee with pre-ground coffee has been requested. Place pre-ground coffee in the funnel and press Tick_Select Button for Oven.PNG to continue and complete delivery

Displayed Mess_Fill Beans Cont.PNG

FILL BEANS CONTAINER

The coffee beans have run out. Fill the beans container.

Displayed Mess_Adjust Mill.PNG

GROUND TOO FINE. ADJUST MILL 1 CLICK WHILE IN OPERATION

The grinding is too fine and the coffee is delivered too slowly or not at all. Repeat coffee delivery and turn the grinding adjustment dial one click clockwise towards ‘7’ while the coffee mill is in operation. If after making at least two coffees, delivery is still too slow, repeat the correction procedure, turning the grinding adjustment dial another click until delivery is correct (see section ‘Adjusting the coffee mill’). If the problem persists, make sure the water tank is fully inserted.
If you’re using a water softener filter, an air bubble may have been released inside the circuit, obstructing delivery Deliver some water through the hot water spout until the flow becomes regular.

Displayed Mess_Select Milder Taste.PNG

SELECT A MILDER TASTE OR REDUCE PRE-GROUND COFFEE QUANTITY

Too much coffee has been used. Select a milder strength by pressing STRENGTH Coffee Strength.PNG or reduce the quantity of pre-ground coffee (maximum 1 measure).

Displayed Mess_Insert Water Spout.PNG

INSERT WATER SPOUT

The hot water spout is not inserted or is not inserted correctly. Insert the water spout as far as it will go

Displayed Mess_Insert Milk Cont.PNG

INSERT MILK CONTAINER

The milk container is not inserted correctly. Insert the milk container as far as it will go.

Displayed Mess_Insert Infuser Assemb.PNG

INSERT INFUSER ASSEMBLY

The infuser has not been replaced after cleaning. Insert the infuser as described in section ‘Cleaning the infuser’.

Displayed Mess_Water Circuit Empty.PNG

WATER CIRCUIT EMPTY PRESS OK TO START FILLING PROCESS

The water circuit is empty.

PressTick_Select Button for Oven.PNGto deliver water from the spout until it flows out normally. Delivery stops automatically.

If the problem persists, make sure the water tank is fully inserted.

Displayed Mess_OK to start Milk .PNG

PRESS OK TO START CLEANING PROCESS OR TURN MILK FROTH ADJUSTMENT DIAL

The milk container has been inserted with the froth adjustment dial in the CLEAN position To proceed with the CLEAN function, press Tick_Select Button for Oven.PNG or turn the froth adjustment dial to one of the milk positions.

Displayed Mess_Tubes inside Milk Cont to be cleaned.PNG

TURN DIAL TO POSITION TO START CLEANING

Milk has been delivered recently and the tubes inside the milk container must be cleaned. Turn the froth adjustment dial to CLEAN.

Displayed Mess_Milk Cont froth adj dial set to clean.PNG

TURN THE MILK FROTH ADJUSTMENT DIAL TO MILK POSITION

The milk container has been inserted with the froth adjustment dial in the CLEAN position. Turn the dial to the required froth position

Displayed Mess_Descaling Needed.PNG

DESCALING NEEDED PRESS OK TO START (~45min)

The machine must be descaled. Press Tick_Select Button for Oven.PNG to start descaling or BACK to descale later. The descaling procedure described in section ‘Descale’ needs to be performed.

Displayed Mess_Water Soft Exhausted.PNG

REPLACE WATER FILTER PRESS OK TO START

The water softener filter is exhausted. Press Tick_Select Button for Oven.PNG to replace or remove the filter, or BACK to carry out the procedure later. Follow the instructions in section ‘Water softener filter’.

Displayed Mess_General Alarm.PNG

GENERAL ALARM: REFER TO USER MANUAL

The inside of the appliance is very dirty Clean the inside of the appliance thoroughly, as described in section ‘Cleaning’. If the message is still displayed after cleaning, contact Customer Care.
Displayed Mess_Needs Descaling.PNG The appliance needs descaling and/or the filter must be replaced. The descaling procedure described in the ‘Descale’ section, needs to be performed and/or the filter needs replacing or removing as described in section ‘Water softener filter’.
Displayed Mess_Tubes in Milk Cont need to be cleaned.PNG The tubes inside the milk container must be cleaned. Displayed Mess_Tubes inside Milk Cont to be cleaned #2.PNG
Turn the froth adjustment dial to CLEAN.
Displayed Mess_Water Filter to be replaced.PNG The filter must be replaced. Replace the filter or remove it as described in section ‘Water softener filter’
Displayed Mess_MUST be Descaled.PNG The machine must be descaled. The descaling procedure described in section ‘Descale’ needs to be performed.
Displayed Mess_Auto Start.PNG The auto-start function is enabled. To disable the function, proceed as described in section ‘Auto start’.
Displayed Mess_Energy Saving Enabled.PNG Energy saving is enabled. To disable energy saving, proceed as described in section ‘Energy saving’.

 

 

 

  • Was this article helpful?