Skip to main content
Fisher & Paykel Product Help

Cleaning

 

 

Cleaning the Appliance

The following parts of the appliance must be cleaned regularly (refer to page 2):

  • The appliance’s internal circuit.
  • Coffee grounds container.
  • Drip tray.
  • Water tank.
  • Coffee spouts.
  • Pre-ground coffee funnel.
  • Infuser, accessible after opening the infuser door.
  • Milk container.
  • Hot water/steam connection nozzle.
  • Control panel.
  • Do not use solvents, abrasive detergents or alcohol to clean the coffee maker. You need not use chemical products to clean the machine.
  • None of the components of the appliance can be washed in a dishwasher with the exception of the milk container.
  • Do not use metal objects to remove coffee deposits as they could scratch metal or plastic surfaces. 

 

Cleaning the Machine’s Internal Circuit

If the appliance is not used for more than three to four days, before using it again, we strongly recommend switching it on and:

  1. Performing two to three rinse cycles by selecting the ‘Rinse’ function (see ‘Rinsing’ section).
  2. Delivering hot water for a few seconds (see ‘Delivering hot water’ section).
After cleaning, it is normal for the grounds container to contain water

 

Cleaning the Coffee Grounds Container

Cleaning_Grounds Cont.PNG

 

When EMPTY GROUNDS CONTAINER appears on the display, the grounds container must be emptied and cleaned. The appliance cannot be used to again until you have cleaned the grounds container. Even if the container is not full, the empty grounds container message is displayed 72 hours after the first coffee has been prepared. For the 72 hours to be calculated correctly, avoid turning the appliance off from the mains switch if it is not necessary

To clean (with the appliance on):

Cleaning_Grounds Cont #1.PNG Cleaning_Grounds Cont #2.PNG
  1. Open the bottom door.
  1. Remove the drip tray, empty and clean.
  2. Empty the grounds container and clean thoroughly to remove all residues left on the bottom. This can be done using the spatula or the brush provided.

 

When removing the drip tray, the grounds container must be emptied, even if it contains few grounds. If this is not done, when you make the next coffees, the grounds container may fill up more than expected and clog the machine. 

 

Cleaning the Drip Tray 

Cleaning_Drip Tray #1.PNG Cleaning_Drip Tray #2.PNG
  1. Remove the drip tray and coffee grounds container.
  2. Empty the drip tray and grounds container and wash them.
  3. Re-insert the drip tray and grounds container back into the appliance.
  • The drip tray is fitted with a level indicator (red) showing the level of water it contains.
  • Before the indicator protrudes from the cup tray, the drip tray must be emptied and cleaned, otherwise the water may overflow the edge and damage the appliance, the surface it rests on or the surrounding area.

 

Cleaning the Inside of the Coffee Maker

Before cleaning internal parts, the appliance must be turned off (see section ‘Turning the appliance off’) and unplugged from the mains power supply. Never immerse the the appliance in water.
  1. Check regularly (about once a month) that the inside of the appliance (accessible after removing the drip tray) is not dirty.
  2. If necessary, remove coffee deposits with the brush supplied and a sponge. Remove all the residues with a vacuum cleaner.
Cleaning_Inside Coffee Maker.PNG

 

Cleaning the Water Tank

  1. Clean the water tank regularly (about once a month) and whenever you replace the water softener filter (if provided) with a damp cloth and little dishwashing liquid. Rinse thoroughly before filling the tank and putting it back in the appliance.
  2. Remove the filter (if present) and rinse with running water.
  3. Replace the filter (if provided), fill the tank with fresh water and place the tank back into the appliance.
  4. For models with water softener filter only: Deliver about 90ml of hot water to reactivate the filter.
Cleaning_Water Tank.PNG

 

Cleaning the Coffee Spouts 

Cleaning_Coffee Spout #1.PNG Cleaning_Coffee Spout #2.PNG
  1. Clean the coffee spouts regularly with a sponge or cloth.
  1. Check that the holes in the coffee spouts are not blocked. If necessary, remove.

 

Cleaning the Pre-ground Coffee Funnel

Check regularly (about once a month) that the pre-ground coffee funnel is not blocked. If necessary, remove coffee deposits with the brush supplied.

 

Cleaning the infuser

The infuser must be cleaned at least once a month.

The infuser must not be removed when the appliance is on. Do not use force to remove the infuser.
  1. Make sure the machine is correctly turned off (see Turning off).
  2. Open the service door.
Cleaning_Infuser #1_2.PNG Cleaning_Infuser #3_4.PNG
  1. Remove the drip tray and waste coffee container.
  1. Press the two coloured release buttons inwards and at the same time pull the infuser outwards.
Do not use dishwashing liquid to clean the infuser as it will remove the lubricant inside the piston.
  1. Soak the infuser in water for about five minutes, then rinse. 
Cleaning_Infuser #5.PNG Cleaning_Infuser #6.PNG Cleaning_Infuser #7.PNG
  1. After cleaning, replace the infuser by sliding it onto the internal support and pin at the bottom, then push the PUSH symbol fully in until it clicks into place.
If you encounter difficulty inserting the infuser, before inserting it you must adapt it to the right dimension by pressing it forcefully from the bottom and top as shown.
  1. Once inserted, make sure the two coloured release buttons have snapped out.
  2. Replace the drip tray and waste coffee container.
  3. Close the service door

 

Cleaning the Milk Container

Cleaning_Milk Container.PNG

 

 

Each time the milk container needs to be re-filled, clean it as described below:

  1. 1 Lift and remove the lid.
  2. Extract the milk container from the thermal casing, holding it by the two side grips.
The thermal casing must not be filled with or immersed in water. Clean with a damp cloth only.
  1.  Remove the milk spout and intake tube.
Cleaning_Removing Milk Spout.PNG Cleaning_Wash Frother.PNG
  1. Turn the froth adjustment dial clockwise to the INSERT position and pull off.
  1. Wash all the components of the frother thoroughly with hot water and dishwashing liquid. All components and the container are dishwasher safe. Make sure there are no milk residues on the hollow and groove under the dial. If necessary, scrape the groove with a toothpick.
  1. Rinse inside the froth adjustment dial seat and the milk frother connector hole.
  2. Check that the intake tube and spout are not clogged with milk residues.
  3. Reposition the dial (lining up the arrow with the word INSERT). Reinsert the spout and milk intake tube.
  4. Place the milk container in the thermal casing.
  5. Place the lid back on the milk container.
Cleaning_Wash Frother #2.PNG

Cleaning the steam connection nozzle

Each time you re-fill the milk container, clean the connection nozzle with a sponge to remove milk residues from the gaskets.

Cleaning_Steam Nozzle.PNG

 

 

 

  • Was this article helpful?