Installation instructions

Last updated
Save as PDF

Please read and follow the ‘Safety and warnings’ and ‘installation instructions’ sections carefully before using your cooker!

Product and minimum clearance dimensions

Screen Shot 2017-06-26 at 12.45.13 PM.png

Screen Shot 2017-06-26 at 12.45.17 PM.png

Product Dimensions

Property (mm)	WA1068P
*Overall height of product (to highest point on console)**	1060 – 1090
Overall width of product	685
Overall depth of product	700
*Height of product to top of lid (closed)**	950 – 980
*Height of lid open (measured from bottom of product)**	1440 – 1470

* Includes adjustable mounted feet and the range of movement.

Minimum Clearances

Property (mm)	WA1068P
Minimum cavity width	725
Minimum depth clearance (including inlet hoses and drain hose)	750
Minimum clearance to adjacent product# (dryer)	20

# Applies either side.

Maximum Capacity

Property (kg)	WA1068P
Maximum Capacity	10.0

Electrical supply: 220 V – 240 V, 50 Hz Sinusoidal, 10 A
Inlet water static pressure: Max. 1 MPa (150 psi), Min. 34 KPa (5 psi)
Inlet water flow rate at tap: Min. 6 litres/min
Standpipe height: 850 – 2400 mm

Unpacking

To ensure the best performance from your new washer please follow the instructions below.

Removing the packaging

Remove the outer packaging.
Tilt the machine backwards and walk it off the base packer one foot at a time (ensure the lid is still taped down).
Remove the base packer from under the machine by tilting the machine backwards and pulling the packer out the front.
Remove the tape, lift the lid and remove the bowl packer from the bowl.
Remove the hoses and accessories.
Keep the base packer and bowl packer in case they are required for future transit.

Screen Shot 2017-06-26 at 12.54.52 PM.png

Tilt washer backwards to remove packer

Please ensure that the base packer has been removed BEFORE OPERATING your machine.

Location

Your washer must be installed on a level surface and not on any textured floor coverings (eg carpet, rugs) to ensure that the opening at the bottom of the machine is not obstructed.

In your clothes washer you will find:

1 hose guide.
2 inlet hoses.

Drain hose

Carefully pull the drain hose out from the back of the machine by pulling the exposed part of the hose downward and outward.
To guide the drain hose over the tub or standpipe the hose guide MUST be fitted to the drain hose.

To prevent siphoning the drain hose should not extend more than 20 mm from the end of the guide. The height of the standpipe or tub should be between 850 – 2400 mm. The drain hose can be trimmed to length.

Place the drain hose in the tub or standpipe. Do not fit the hose to a drain spigot. Drainage must not be airtight in order to prevent siphoning.

Screen Shot 2017-06-26 at 12.55.02 PM.png

Fitting the drain hose guide

Electrical

This appliance must be supplied with a 220 – 240 V, 50 Hz, sinusoidal, 10 A electrical supply.

Draining

Regularly check that your standpipe or tub is free from lint or other obstructions, which may affect how your machine works or may cause flooding.
In multi-storey apartments or any upper floor, the machine should be installed on a floor equipped with a drain.
Draining must comply with local by-laws.

Water supply

Your cold water should not exceed 35°C and your hot water should not exceed 65°C. Temperatures above these may cause the machine to fault or cause damage to the machine.
If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should fit a Safe Valve. This will ensure the hot water temperature remains within safe limits.
Inlet water static pressure: Max.1 MPa (150 psi) Min. 34 KPa (5 psi)
Inlet water flow rate at tap: Min. 6 litres/min

Hot ‘N’ Safe Valves available are:

RMC TVA 50HF

RMC TVA 75HFS
Adjustable between 35°C – 55°C

RMC TVA 50HP
For instantaneous gas hot water supply

Inlet hoses

New hose sets provided with the washer shall be used to connect the washer to the water mains.

Old hose sets should not be re-used.

Connect the straight ends of the inlet hoses to the taps (there are washers fitted in both ends). Connect the red connector hose to Hot, and the white connector hose to Cold.
Connect the elbow ends of the inlet hoses to the corresponding machine inlet valves. Inlet valves are marked on the back of the machine. Ensure the Hot valve is connected to the hot tap and the Cold valve is connected to the cold tap.

H = Hot C = Cold

Screen Shot 2017-06-26 at 12.59.54 PM.png

Inlet hose ends

Cold supply only:

If you only have a cold water supply, an inlet valve cap (blanking cap) MUST be connected to the Hot inlet valve. The cap prevents water leaking out of the hot
valve. The cap is available from your Fisher & Paykel dealer or Authorised Repairer,
Part No. 388491P. This appliance incorporates backflow protection complying with AS3500.1. No further backflow protection is required for connection to the water supply.

Your washer does not have an internal heater to heat water.

Inlet hose replacement

We recommend replacing the inlet hoses every 5 years. Hoses should be checked from time to time and replaced if any wear, cuts, bulges, kinks or leaks are found.

Failure to do so may result in a flood and damage to property.

Levelling instructions

It is IMPORTANT to level the machine to ensure good spin performance and effective detergent and fabric softener dispensing.

A spirit level is provided with your machine. Use this to level your machine, always placing it on a clean, flat surface. The machine is level when the bubble sits in the centre, within the two lines.

Your washer is equipped with self-locking feet to ensure they do not move once you have levelled your machine. To adjust the feet, pull down then twist to move them up or down.

After levelling, the corners of the washer should be clear of the floor and the machine must not rock in any direction.

Move the machine to its final position using the top corners to manoeuvre the product into place (do not push on the centre front of the machine). We recommend a minimum clearance of 20 mm each side and 50 mm at the rear of the machine.
With the lid closed, place the spirit level at the centre back of the lid (near the control panel). Pull the machine out and adjust the rear feet (wind down) until the machine is level side to side when in position.	Levelling – Step 2
Open the lid. Place spirit level on the flat surface on the left side, inline with the centre of the bowl. Adjust the front left foot (wind down) until the machine is level.	Levelling – Step 3
Move the spirit level to the right side, in line with the centre of the bowl. Adjust the front right foot (wind down) until the machine is level, and does not rock. There should be equal weight on both front feet so that neither can be turned by hand when the machine is in position.	Levelling – Step 4
Place the spirit level at the centre front of the topdeck, forward of the lid lock slot. Check the machine is level. Move the spirit level around to all positions once more, checking the machine is level in all areas. Check the machine does not rock side to side, front to back, or corner to corner.	Levelling – Step 5

Keep your spirit level for the next time you move or reposition your washer.

If moving or transporting your washer in the future, ensure you tape the lid down beforehand.

Completing your installation

Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hoses. Check the hose connections for leaks again after 24 hours.
Uncoil power cord, remove and discard the plastic pin cover, and plug into wall socket.

Installation test cycle

Your washer must be correctly installed before use. Check the installation and operation of the machine using the following procedure:

Touch to activate your washer.
Touch both the and ‘Options’ buttons at the same time, and hold for three seconds.
Touch to start the installation test cycle.
The machine will beep to signal the end of the installation test cycle. Any faults will be displayed on the screen (refer to 'Fault codes'). If you need further assistance, please contact a Fisher & Paykel Customer Care Representative. Refer to 'Customer Care' for contact details.

if there are no faults found, the washer will automatically turn off at the end of the installation test cycle.

Accessories and Spare Parts

Available from your Fisher & Paykel dealer or a Fisher & Paykel Authorised Repairer.
Inlet Valve Cap	Part No. 388491P
Hose Inlet Long (2 m)	Part No. 422680P
Hose Inlet Large Bore	Part No. 426123P
Drain Hose Extension	Part No. 425627P
Power Cord	If the power cord of your clothes washer is damaged it must be replaced by a Fisher & Paykel Authorised Repairer in order to avoid a hazard, as it is not a standard power cord.